Failed to Read Sector at Offset 301558548480. (0x00000017) Log Error: 0xc0000037

You are using an out of date browser. Information technology may not display this or other websites correctly.
You should upgrade or use an alternative browser.

• #1

Hello,

I try again only I will be shorter this time in the description of my problem.

Is there someone that tin can tell me how I can program my smarphone when SP Flash Tool brandish this error bulletin: Mistake: status_brom_cmd_send_da_fail (0xC0060003) ?

See fastened movie.

Thanks for your help.

Attachments

• 

• #2

I accept the aforementioned result whatever oNe .???

• #3

Hi , try this :
i. Unplug your device from pc
2. Open Sp Flash Tool with Administrator privileges
three. Go to Download and put scatter.txt file
four. Now go to Format and make sure that yous have checked Auto Format Wink and Format whole except Bootloader , click on Start , wait few second and close Confirmation popup.
5. At present become to Download and instead of Download but exercise Format All + Download .

If not , effort so Upgrade only or endeavor to flash with another version of wink tool .

Good Luck

Final edited: Nov 24, 2017

• #four

Howdy,

Finally I found the way to program the smartphone.

- Plough off your mobile phone
- Press Download (SP Button) in SP Flash Tool
- Press Volume Down on the mobile phone.
- Go along Volume Down pressed and connect to the USB
- Normally SP Flash tool starts to program and y'all can release the Volume Down key.

Hop it will piece of work for you.

• #5

Hello,

Finally I found the way to program the smartphone.

- Turn off your mobile phone
- Press Download (SP Push) in SP Flash Tool
- Press Volume Down on the mobile phone.
- Keep Volume Downward pressed and connect to the USB
- Usually SP Flash tool starts to programme and you can release the Volume Down key.

Hop information technology will piece of work for you.

didnt worked for me

• #half dozen

possibly solution

Then i had the aforementioned problem and the solution for me was to hold volume upwards cardinal as i was connecting and keep pressing until the red bar is 100% then later a few seconds release it.

Apparently i cant post links but i volition re-create the tutorial.

With the phone off:

- Click DOWNLOAD in SP Flash Tool
- Agree VolumeUp on your phone
- Connect the phone while still holding VolumeUp
- Hold VolumeUp a couple of seconds after the cerise bar gets to 100%
- Release

Credit to GizBeat on chinaphonearena.

• #vii

What worked for me ...

Subsequently following
https://www.getdroidtips.com/flash-stock-firmware-using-sp-wink-tool/
I got the
fault status brom cmd send da neglect 0xc0060003
message.

I started doing what was said past Teddy Lo, but information technology was non meliorate.

I kept my current cession (SP Wink Tools v.1752 started with administrative mode);
went into format tab, left FORMAT WHOLE EXCEPT BOOTLOADER
clicked on Kickoff, then End
then in download TAB
in the select card, choose format+download
click DOWNLOAD push
... got the 0xc0060003 message ...
but ... immediately abolish this pop-up and reclick on DOWNLOAD asap. And and then, flash goes fine (DA once again with scarlet bar, and so, all partitions with yellowish bar).

This way, I have been able to reinstall ROM v6 on Oukitel K6000 Plus.

Never had to press down or up book during first-upward; just let phone boot; or press voldown+power to end/restart it, if it is already started somehow. My phone was in orange state, and my system was completely cleaved (non bootable, not usable). I only had working bootloader and recovery; I tried diverse other ways to install stock ROM, all failed. I had boot loops and other bug. In the end, I went back to SPFT, and just cancelling and reclicking ASAP on the DOWNLOAD push did information technology for me.

At present trying ROM v23 ... (will edit in 1h about it).

... happily for you, my windows crashed, and I had to restart the whole process, and so now I can write down the working process:
- phone was upwards with ROM v6 working fine
- phone was plugged on USB
- previously installed VCOM
- could non install Android/Download commuter
- Oukitel K6000 Plus
- SPFT 5.1752 started with admin perms
- DA already set to MTK_AllInOne_DA.bin
- scratter ... the merely file available in the binder containing my new rom (official V23 from Oukitel, downloaded last year, then forgot where I took information technology - yes it's ane year I am trying to upgrade)
- in the card, select format all + download
- go in format TAB
- tick Car format
- tick FORMAT ALL except bootloader
- exit validation unticked
- click on START, await 5s, click STOP
- back in Download tab
- click DOWNLOAD button
- press voldown+power to reboot the phone
- got the pop-upward once with error 0xc0060003
- immediately cancel the pop-up and reclick DOWLOAD button
- got the pop-up a second fourth dimension, cancel information technology a 2d fourth dimension, click DOWNLOAD a third time
- sweat a lot ... DA once again ... partitions again, yellow lines ... V23 installed \o/

Some steps may be be useless or optionnal; this was the raw log/history of what I did to piece of work around "error status brom cmd transport da fail 0xc0060003".

First boot is VERY long ...

• #8

"Download-agent" DA_PL

Hi, guys !
I faund decision for me.
- When you opened Flash Tool, next you need choose "Download-agent" DA_PL (not MTK_AllInOne_DA)
it'southward works for me

• #nine

Thanks. It worked for me too.

Hi, guys !
I faund decision for me.
- When you opened Wink Tool, next you demand choose "Download-agent" DA_PL (non MTK_AllInOne_DA)
it's works for me

You saved me a day!

Thanks a lot :expert: :victory:

• #10

YES! Cheers!

This worked for me and finally unbricked this inexpensive Leagoo S8 that bricked itself!
You rule.
Thanks.

Hullo,

Finally I establish the way to program the smartphone.

- Turn off your mobile phone
- Press Download (SP Button) in SP Flash Tool
- Press Volume Downwards on the mobile phone.
- Continue Book Downward pressed and connect to the USB
- Normally SP Wink tool starts to programme and you can release the Book Down central.

Hop it will piece of work for you.

• #eleven

Sp flash tool mistake 0xc003003

Hello I proceed getting this fault status da selection 0xc0030003

And I cant discover any info online to fix I am trying to flash a elephone p9000 afterwards a screen replacement

Any help or advice would exist great help

• #12

Hello I keep getting this error condition da selection 0xc0030003

And I cant find any info online to set I am trying to flash a elephone p9000 later on a screen replacement

Any help or advice would be great aid

1. In that location are ii stock ROMs officially bachelor for your device. Are you sure you are using the correct 1?

two. Are you sure you are using a compatible download agent (DA)? If the default "MTK_AllInOneDA.bin" isn't working, check your ROM nothing to see if you have anything else... Perchance DA_PL.bin, DA_SWSEC.bin or DA_SWSEC_CRYPTO20.bin might piece of work for your device.

The error you are getting makes it articulate that y'all are trying to utilize an incompatible DA.

Look into my suggestions, and if you nonetheless get the error, I'd recommend you to create a new thread, where yous're more than likely to get assist (and sooner besides).

• #xiii

Hello I proceed getting this error condition da selection 0xc0030003

And I cant find any info online to fix I am trying to flash a elephone p9000 after a screen replacement

Any aid or communication would be groovy help

Thanks I am new to android I am thinking your right I need to look close at what software information technology is I think iv been at it all day so I thought I would ask many thanks

• #14

cheque out Unlockcafe on youtube and instagram, he can fix that

• #xv

What worked for me ...

Later following
https://www.getdroidtips.com/wink-stock-firmware-using-sp-wink-tool/
I got the
mistake status brom cmd send da neglect 0xc0060003
message.

I started doing what was said past Teddy Lo, but it was not better.

I kept my current cession (SP Flash Tools 5.1752 started with administrative mode);
went into format tab, left FORMAT WHOLE EXCEPT BOOTLOADER
clicked on START, then Cease
so in download TAB
in the select carte du jour, choose format+download
click DOWNLOAD button
... got the 0xc0060003 bulletin ...
but ... immediately cancel this popular-upwards and reclick on DOWNLOAD asap. And then, flash goes fine (DA again with red bar, then, all partitions with yellow bar).

This style, I have been able to reinstall ROM v6 on Oukitel K6000 Plus.

Never had to press down or upwardly book during start-up; only allow telephone boot; or press voldown+power to finish/restart it, if information technology is already started somehow. My phone was in orange state, and my arrangement was completely broken (not bootable, not usable). I only had working bootloader and recovery; I tried diverse other ways to install stock ROM, all failed. I had boot loops and other bug. In the end, I went back to SPFT, and just cancelling and reclicking ASAP on the DOWNLOAD push button did it for me.

Now trying ROM v23 ... (volition edit in 1h about information technology).

... happily for you, my windows crashed, and I had to restart the whole process, then at present I can write down the working procedure:
- phone was up with ROM v6 working fine
- phone was plugged on USB
- previously installed VCOM
- could not install Android/Download driver
- Oukitel K6000 Plus
- SPFT v.1752 started with admin perms
- DA already set to MTK_AllInOne_DA.bin
- scratter ... the only file available in the binder containing my new rom (official V23 from Oukitel, downloaded concluding year, and so forgot where I took it - yes it's one twelvemonth I am trying to upgrade)
- in the menu, select format all + download
- go in format TAB
- tick Motorcar format
- tick FORMAT ALL except bootloader
- leave validation unticked
- click on First, look 5s, click Stop
- back in Download tab
- click DOWNLOAD button
- press voldown+ability to reboot the phone
- got the pop-up once with mistake 0xc0060003
- immediately cancel the pop-up and reclick DOWLOAD button
- got the popular-upwardly a 2nd time, abolish it a second time, click DOWNLOAD a third time
- sweat a lot ... DA again ... partitions again, yellow lines ... V23 installed \o/

Some steps may be be useless or optionnal; this was the raw log/history of what I did to work effectually "fault status brom cmd send da fail 0xc0060003".

Starting time boot is VERY long ...

did not piece of work

• #16

thanks you saved me

:highfive:

Hullo, guys !
I faund decision for me.
- When you opened Flash Tool, adjacent y'all demand choose "Download-agent" DA_PL (not MTK_AllInOne_DA)
it's works for me

• #17

Bien bonjour, je voudrais aussi flasher un tecno camon 11 mais j'ai aussi fifty'erreur brom cmd ship da fail 0xc0060003, svp que quelqu'un m'aide d'urgence

• #18

I still have 0xC0060003 fault

Hi,
I yet have 0xC0060003 fault.
After the ruddy line fills 100% it volition get stuck and within 9 seconds and fails.

someone help me
my phone is HTC, MT65xx

• #19

solution 101

Hey guys, For those people out there whos' trouble stays the aforementioned and the above-given solutions don't work cause I know, it doesn't work in all phones(I've tried it several times and stock on the same error). I've been researching this problem and none appears to be the solution that works. From the hints that I've gathered this solution work for me and might exist for you lot as well.

Assuming you have opened the SP flashtool and the scatter file is placed.
1. click download
ii. connect your phone
3. list downwardly all the names that caused your trouble and do information technology several times
#for me : systeminfo, sutinfo, cda and recovery are the causes.

four. uncheck all the problems until none remains and you're done.

I hope this works on you guys. :skilful:

• #twenty

Haven't worked

Howdy , try this :
i. Unplug your device from pc
ii. Open Sp Flash Tool with Ambassador privileges
3. Go to Download and put scatter.txt file
four. Now go to Format and make sure that y'all have checked Auto Format Wink and Format whole except Bootloader , click on Starting time , wait few second and close Confirmation popup.
5. Now get to Download and instead of Download just practice Format All + Download .

If non , effort then Upgrade only or try to flash with some other version of wink tool .

Good Luck

Deplorable, Merely haven't worked for me, got the same fault also while doing format.Please Aid. Actually i am having lenovo k8 note and till yesterday, it was showing the popular-up that driver haven't installed because device is unplugged but i think that was due to bad data cable, so i changed that one and at present i am having the error(0xc0060003). Don't know what to do next ,PLEASE HELP.

Similar threads

owenlondied1962.blogspot.com

Source: https://forum.xda-developers.com/t/brom-error-status_brom_cmd_send_da_fail-0xc0060003.3707811/

Share this post